Mobilect 39
電氣絕緣油
產品描述
mobilect?39是一種高質量的絕緣油與礦物不羈非常良好的介電性能和氧化穩定性，用于變壓器，開關和其他電氣設備。
39是mobilect不羈和符合標準IEC 60296（04）和ASTM d1275b / CIGRE腐蝕試驗要求。
特點和優點
mobilect 39具有高的耐熱和化學在鐵和銅的存在下的降解，從而減少傾向產生污泥和油溶性氧化產物。當?shù)唾|(zhì)量的油被使用時，這些可能會形成在變壓器的存款，并阻礙對流電流的干擾傳熱。此外，存款可能會加速絕緣缺陷，往往是非常困難的，沒有完整的拆除拆除。
mobilect 39是專門處理以除去水分在制造。水將減少石油的電絕緣性能，促進氧化。是要記住，干油的吸濕性，吸收空氣中的水分很重要。因此，它必須始終存放在干燥的條件和良好的封閉容器。強烈建議在使用前將產品干燥，或在采購后短時間內使用，以避免長期儲存。
39的mobilect介電強度是電應力對油的抵抗程度是千伏在規定的試驗條件下表達的差距。這不是一個衡量的石油質量，但沒有污染物-特別是水分，纖維和極性化學品。
mobilect 39無蠟，即使在較低的溫度，從而自由流通，在戶外應用。它的粘度確保容易通過移動對流換熱。流動性也是必不可少的開關設備中的電弧快速淬火。
低倒mobilect 39點保證在大多數情況下自由流動之間的變壓器儲油柜與保持在最低溫度開關的可靠性。
應用
mobilect 39推薦使用的充油變壓器和開關設備中的油應作絕緣介質或作為傳熱介質。
mobilect 39是用在應用程序指定的IEC 60296（04）一般規格和增強銅的腐蝕保護（通過ASTM d1275b腐蝕試驗）。
mobilect 39不適用于充油電纜、特種浸漬過程中使用的電容器或。
Mobilect? 39
Electrical insulating oils
Product Description
Mobilect? 39 is a high quality mineral uninhibited insulating
oil with very good dielectric properties and oxidation stability intended for
transformers, switchgears and other electrical equipment.
Mobilect 39 is uninhibited and meets the specifications IEC
60296 (04) and ASTM D1275B / CIGRE corrosion tests requirements.
Features and Benefits
-
Mobilect 39
has a high resistance to thermal and chemical degradation in the presence
of iron and copper, which reduces tendencies to produce sludge and
oil-soluble oxidation products. When lower quality oils are used these may
form deposits in the transformer and impede heat transfer by interfering
with convection currents. In addition deposits may accelerate insulation
defects and are often very difficult to remove without complete
dismantling.
-
Mobilect 39
is specifically treated during manufacture to remove moisture. Water will
reduce the electrical insulating properties of the oil and promote
oxidation. It is important to remember that a dry oil is hygroscopic and
absorbs moisture from the air. It must therefore always be stored in dry
conditions and well-closed containers. It is strongly recommended to dry
the product before use or use it within short notice after purchasing to
avoid long term storage.
-
The
dielectric strength of Mobilect 39 is a measure of the resistance of the
oil to electric stress and is expressed in kV across a specified gap under
test conditions. This is not a measure of the quality of the oil but of
the absence of contaminants - especially moisture, fibres and polar
chemicals.
-
Mobilect 39
is free from wax even at low temperatures and thus circulates freely in
outdoor applications. Its viscosity ensures readily heat transfer by
mobile convection currents. Mobility is also essential to quick quenching
of arcs in switchgear units.
-
The low pour
point of Mobilect 39 ensures a free flow in most conditions between the
transformer and the conservator and maintains the reliability of tap
changers at the lowest temperatures.
Applications
-
Mobilect 39
is recommended for use in oil filled transformers and switchgears in which
the oil is required as an insulation medium or as a heat transfer medium.
-
Mobilect 39
is to be used in applications specifying IEC 60296 (04) General
Specifications and reinforced copper corrosion protection (pass ASTM
D1275B corrosion test).
-
Mobilect 39
is not suitable for use in oil filled cables, for special impregnation
processes or for use in capacitors.
Specifications and Approvals
|
Mobilect 39 meets or exceeds the requirements of:
|
|
|
IEC
60296 (04) General Specifications
|
|
Typical Properties
|
Mobilect 39
|
|
|
Density
at 20°C, kg/dm3, ISO 12185
|
0.883
|
|
Viscosity,
mm2.s-1 @ 40°C, ISO 3104
|
9.5
|
|
Flash
Point (PMCC), °C, ISO 2719
|
148
|
|
Pour
Point, °C, ISO 3016
|
-
54
|
|
Corrosive
Sulphur, ASTM D1275 procedure B
|
Non
Corrosive
|
|
Oxidation
Stability @ 120°C /164 h, IEC 61 125C
|
|
|
-
Total Acidity, mg KOH/g
|
0.31
|
|
-
sludge, wt%
|
0.11
|
|
Dielectric
Dissipation Factor @ 90°C, IEC 60247
|
?
0.001
|
|
Interfacial
Tension, mN/m, ISO 6295
|
?
40
|
|
Breakdown
voltage,
|
|
|
-
before treatment, kV, IEC 60156
|
?
30
|
|
-
after treatment, kV, IEC 60156
|
?
70
|
 |
